Aem 30-3438 Series 2 AEMnet Adapter Manual de usuario

Busca en linea o descarga Manual de usuario para Para El Coche Aem 30-3438 Series 2 AEMnet Adapter. AEM 30-3438 Series 2 AEMnet Adapter User Manual Manual de usuario

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 7
  • Tabla de contenidos
  • MARCADORES
  • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 0
AEM Performance Electronics
2205 W 126
th
Street Unit A, Hawthorne, CA 90250
Phone: (310) 484-2322 Fax: (310) 484-0152
http://www.aemelectronics.com/
Instruction Part Number: 10-3438 Rev 1
2011 AEM Performance Electronics, Inc.
Page 1
AEMnet
AEMnet is an open architecture software and hardware interface based on the CAN 2.0 specification,
which provides the ability for multiple AEMnet enabled devices to easily communicate with each other
through a single cable. The hardware connection is made through a Deutsch 4P DTM connector.
Devices connected to the AEMnet transmit data through this one connection. Once the AEMnet
adapter is installed, the Series 2 EMS will be able to send and receive data on the AEMnet.
Instructions for configuring the Series 2 EMS to output data are included in this manual. Instructions
on configuring the Series 2 EMS to receive data from other AEMnet enabled products are contained
in the individual product manuals. Upon completion of these instructions, the Series 2 EMS will be
configured to output data to an AQ1 Data Logger or other data receiving device.
The following AEM products are currently AEMnet enabled:
Series 2 Engine Management System
EMS-4 Universal Standalone Engine Management System
4-Channel Wideband UEGO Controller
AQ-1 Data Logger
Dyno Shaft On-Vehicle Dynamometer
Instruction Manual
P/N 30-3438 AEMnet Adapter Harness Installation
for Seri
es 2 EMS
30
-
6820 & 30
-
6821
Vista de pagina 0
1 2 3 4 5 6 7

Indice de contenidos

Pagina 1 - Instruction Manual

AEM Performance Electronics 2205 W 126th Street Unit A, Hawthorne, CA 90250 Phone: (310) 484-2322 Fax: (310) 484-0152 http://www.aemelectronics.com/

Pagina 2 - AEMnet CONNECTORS

Page 2 AEMnet CONNECTORS The AEMnet has four wires, two are for communication (white pin 1 and green pin 2) and two are for powering (red pi

Pagina 3

Page 3 REMOVE EXISTING WIRES FROM ECU PLUG(S) 1. Locate a small screwdriver (a precision 1mm wide flathead screwdriver is recommended) and

Pagina 4

Page 4 2. Next remove the pin from the plastic connector by inserting the removal tool (factory recommended part available at Digikey, numb

Pagina 5

Page 5 4. Make sure that the clip that holds the pin in the ECU connector is up so that it will clip properly into the connector. To instal

Pagina 6 - CONFIGURING THE SERIES 2 EMS

Page 6 CONFIGURING THE SERIES 2 EMS The AEMnet data stream is compatible with version AEM25 01v23 firmware and later. To activate the AEMnet

Pagina 7 - WARRANTY

Page 7 WARRANTY 12 MONTH LIMITED WARRANTY Advanced Engine Management Inc. warrants to the consumer that all AEM High Performanc

Comentarios a estos manuales

Sin comentarios