Aem 30-2310 Inline Wideband UEGO Controller Manual de usuario Pagina 1

Busca en linea o descarga Manual de usuario para Para El Coche Aem 30-2310 Inline Wideband UEGO Controller. AEM 30-2310 Inline Wideband UEGO Controller User Manual Manual de usuario

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 8
  • Tabla de contenidos
  • MARCADORES
  • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 0
Part Number 30-2310
INLINE WIDEBAND UEGO CONTROLLER
Figure 1. Wiring Schematic
Inline Wideband UEGO Controller Parts
1 x 30-2310 Inline Wideband UEGO Module
1 x 30-2001 UEGO Sensor
1 x 35-8535 Install Kit (UEGO Bung and 6 Butt Connectors)
1 x 10-2310 Installation Instructions
2 x Zip Tie
INSTALLATION
1. Disconnect the negative battery cable.
2. Find a suitable in-cab or under hood mounting location for the Inline UEGO
controller, away from any direct heat or water sources and shielded from the
elements. Secure the controller using the supplied zip ties as shown in Figure 3.
3. Connect the flying lead wires as shown in Figure 1.
4. Mount the UEGO sensor as shown in figure 2.
5. Plug the UEGO sensor connector on the UEGO controller into the mating
connector on the UEGO sensor.
AEM Performance
Electronics
2205 126
th
Street Unit A, Hawthorne, CA.
90250
Phone: (310) 484-2322 Fax: (310)
484-0152
http://www
.
aemelectronics.com
Instruction Part Number: 10-2310 Rev
02
© 2011 AEM Performance
Electronics
Vista de pagina 0
1 2 3 4 5 6 7 8

Indice de contenidos

Pagina 1 - Part Number 30-2310

Part Number 30-2310 INLINE WIDEBAND UEGO CONTROLLER Figure 1. Wiring Schematic Inline Wideband UEGO Controller Parts 1 x

Pagina 2

Page 2 RED - Connect to a switched, fused (5A) 12 volt power source. BLACK – Connect to a clean power ground. WHITE - Connect to Lambda + Input. BROW

Pagina 3

Page 3 ZIP TIES Figure 3. Inline Wideband UEGO Controller Mounting Indicator Lights The Inline Wideband UEGO Controller has two indicat

Pagina 4

Page 4 UEGO Analog Output The analog output from the Inline Wideband UEGO controller is a linear dc voltage signal that varies from 0.5 Vdc at 8.5:1

Pagina 5

Page 5 Voltage AFR Voltage AFR Voltage AFR Voltage AFR 0.00 8.43 1.40 10.64 2.81 13.99 4.21 17.31 0.16 8.43 1.56 11.02 2.96 14.34 4.37

Pagina 6

Page 6 Inline Wideband UEGO/AEM F/IC Configuration With an FIC calibration open, go to Setup>Aux Gauge, and complete the Aux gauge setup window as

Pagina 7

Page 7 Figure 6. PC Data Viewer The grey wire from the UEGO Controller outputs the data stream in an RS232 serial format. To connect to the pc/l

Pagina 8

Page 8 Specifications UEGO Controller Supply Current (nominal, peak) 1.3A, 2.7A peak Differential Analog Outputs 1 Measuring Range: UEGO 8.5:1 to

Comentarios a estos manuales

Sin comentarios