Aem 30-6905 Universal Programmable EMS-4 Manual de usuario Pagina 23
- Pagina / 279
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Page 23 of 279 EMS-4 Install and Tuning Guide_Rev 1.6
Coil 3 Output
22
Dk Blue
IGN 3
Coil 4 Output
22
Dk Blue
IGN 4
Fused Coil Power
14
Red
COIL PWR
Coil Ground
14
Black
PWR GND
Warning! - The ignition outputs from the EMS-4 are not designed to trigger an ignition
coil directly. Connecting them to a coil that does not contain a built-in driver will damage
the EMS-4. Coils without built-in drivers typically have only two pins on the connector.
Coils with built-in drivers typically have 4 or more pins on the connector. If you are not
sure what kind of ignition coils you have, contact AEM tech support for help.
IGN 1 – Connect to 1
st
coil driver to fire.
IGN 2 – Connect to 2
nd
coil driver to fire.
IGN 3 – Connect to 3
rd
coil driver to fire.
IGN 4 – Connect to 4
th
coil driver to fire.
COIL PWR – Fused coil power. Splice required number of power leads and distribute to each
coil.
PWR GND – Ignition power ground.
AEM Kit P/N 30-2840 (Optional) Four Channel Coil Driver is custom manufactured to AEM‟s
specifications by HÜCO Electronic GmbH in their ISO 9001 facility in Germany. It has been
specially designed by AEM for driving the high power dwell controlled ignition coils commonly
found on performance engines.
The 30-2840 Kit contains:
Four Channel Coil Driver
Five Pin Mating Connector
Four Pin Mating Connector
10 Terminals & Wire seals (one extra of each as a precaution)
Mounting hardware
Thermal Grease
- EMS P/N 30-6905 1
- Revision History 2
- Table of Contents 3
- General Information 6
- Electronics Warranty 6
- Part 1 – EMS-4 Installation 7
- Grounding 17
- USB Connector 18
- CAN Connector 19
- Injectors 19
- Injector Harness Connections 20
- Coil Harness Connections 22
- Coil Driver Connections 24
- FALLING 25
- EDGE FIRE 25
- RISING EDGE 25
- MAP Sensor 26
- Air Temp Sensor 27
- Crank Sensor 29
- Hall Effect voltage signal 30
- Cam Sensor 33
- Vehicle Speed Sensor (VSS) 34
- DO NOT CONNECT 36
- DIRECT TO BATTERY 36
- Part 2 – AEM Tuner 37
- AEM Tuner 39
- Basic Terminology 40
- Menu Items 42
- Calibration Notes 43
- File-Workspace 43
- Edit Menu 44
- Display Menu 45
- Display Explorer 45
- Coils Display 46
- Injectors Display 47
- AEM Tuner Tabs 47
- Tabs Menu 48
- Tabs Menu Detail 48
- EMS Menu 49
- Upload Calibration Dialog 50
- Set Password Dialog 51
- Logging Menu 52
- Tools Menu 56
- Configure Outputs Dialog 56
- Output Activation Criteria 57
- Telemetry Setup Menu Items 58
- Compare - Open File Window 59
- Calibration Compare Dialog 59
- Compare Calibration Detail 59
- Configure Conversion Dialog 61
- Unit Preferences 62
- Unit Preferences Detail 62
- Display Preferences 63
- Hotkey Preferences 64
- Hotkey Detail 64
- Logging Preferences 65
- Calibration Edit Preferences 66
- Quick Tune Preferences 67
- Application Preferences 68
- Wizards Menu Item 69
- Setup Wizards 70
- Configure Gear Ratio Wizard 73
- Live Tracing Menu 74
- Help Menu 75
- AEM Tuner Updates Feature 76
- Editing Options Displays 77
- Available Options 78
- Selected Options 78
- Editing 2D Table Displays 81
- Editing Channel Displays 89
- Editing 3D Map Displays 90
- Part 3 – Tuning Guide 98
- Timing which 99
- Calibration Setup 100
- Timing Pattern Basics 101
- A more complex example 106
- Set up RPM and Load axes 114
- EFI Sensors 115
- Air Temperature Sensor 119
- Water Temp Sensor 120
- (Oxygen) Sensors 120
- Knock Sensor 125
- Sensor Calibration 126
- Set Throttle Range Wizard 131
- Fuel System Setup 134
- Fuel Pump Sizing 135
- Fuel Pump Location 136
- Fuel Hoses and Routing 136
- Fuel Delivery Hose Sizes 137
- Fuel Filter and Fuel Rail 137
- Basic Tuning 142
- Ignition Synchronization 146
- Ignition Timing Sync Wizard 147
- Idle Air Control 150
- Typical Idle Setup Tab 151
- Fuel Tuning 158
- Ignition Tuning Theory 182
- Ignition Map 193
- Ignition Trims 193
- Vehicle Speed 197
- EMS-4 GPIOs 199
- Data logging 209
- Logging Conditions 213
- Logging Custom Conditions 214
- Log Switch Settings 214
- Download EMS Log Menu Item 215
- Advanced Tuning 216
- Knock Control 231
- Traction Control 233
- 2Step Rev Limiter 242
- O2 Feedback 245
- 2-D Tables for O2 Feedback 247
- O2 FB 249
- Nitrous Control 252
- Anti-Lag 256
- Analog Input Switch 259
- Staged Injection 260
- Switched Ignition Retard/Cut 266
- Switch Rtd Step: 268
- Glossary of Terms 269
Relacionado con productos y manuales para Para El Coche Aem 30-6905 Universal Programmable EMS-4
(15 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.045 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales